Bandage is threaded with photonic fibres that change colour to signal pressure level
Bio

Compression therapy is a standard form of treatment for patients who suffer from venous ulcers and other conditions in which veins struggle to return blood from the lower extremities. Compression stockings and bandages, wrapped tightly around the affected limb, can help to stimulate blood flow. But there is currently no clear way to gauge whether a bandage is applying an optimal pressure for a given condition.

Now engineers at MIT have developed pressure-sensing photonic fibres that they have woven into a typical compression bandage. As the bandage is stretched, the fibres change colour. Using a colour chart, a caregiver can stretch a bandage until it matches the colour for a desired pressure, before, say, wrapping it around a patient’s leg.

The photonic fibres can then serve as a continuous pressure sensor — if their colour changes, caregivers or patients can use the colour chart to determine whether and to what degree the bandage needs loosening or tightening.

“Getting the pressure right is critical in treating many medical conditions including venous ulcers, which affect several hundred thousand patients in the US each year,” says Mathias Kolle, assistant professor of mechanical engineering at MIT. “These fibres can provide information about the pressure that the bandage exerts. We can design them so that for a specific desired pressure, the fibres reflect an easily distinguished colour.”

Kolle and his colleagues have published their results in the journal Advanced Healthcare Materials. Co-authors from MIT include first author Joseph Sandt, Marie Moudio, and Christian Argenti, along with J Kenji Clark of the University of Tokyo, James Hardin of the United States Air Force Research Laboratory, Matthew Carty of Brigham and Women’s Hospital-Harvard Medical School, and Jennifer Lewis of Harvard University.

Natural inspiration


The colour of the photonic fibres arises not from any intrinsic pigmentation, but from their carefully designed structural configuration. Each fibre is about 10 times the diameter of a human hair. The researchers fabricated the fibre from ultrathin layers of transparent rubber materials, which they rolled up to create a jelly-roll-type structure. Each layer within the roll is only a few hundred nanometres thick.

In this rolled-up configuration, light reflects off each interface between individual layers. With enough layers of consistent thickness, these reflections interact to strengthen some colours in the visible spectrum, for instance red, while diminishing the brightness of other colours. This makes the fibre appear a certain colour, depending on the thickness of the layers within the fibre.

“Structural color is really neat, because you can get brighter, stronger colors than with inks or dyes just by using particular arrangements of transparent materials,” Sandt says. “These colors persist as long as the structure is maintained.”

The fibres’ design relies upon an optical phenomenon known as ‘interference’, in which light, reflected from a periodic stack of thin, transparent layers, can produce vibrant colours that depend on the stack’s geometric parameters and material composition.

Optical interference is what produces colourful swirls in oily puddles and soap bubbles. It’s also what gives peacocks and butterflies their dazzling, shifting shades, as their feathers and wings are made from similarly periodic structures.

“My interest has always been in taking interesting structural elements that lie at the origin of nature’s most dazzling light manipulation strategies, to try recreating and employing them in useful applications,” Kolle says.

A multilayered approach


The team’s approach combines known optical design concepts with soft materials, to create dynamic photonic materials.

While a postdoc at Harvard in the group of Professor Joanna Aizenberg, Kolle was inspired by the work of Pete Vukusic, professor of biophotonics at the University of Exeter in the UK, on Margaritaria nobilis, a tropical plant that produces extremely shiny blue berries. The fruits’ skin is made up of cells with a periodic cellulose structure, through which light can reflect to give the fruit its signature metallic blue colour.

Together, Kolle and Vukusic sought ways to translate the fruit’s photonic architecture into a useful synthetic material. Ultimately, they fashioned multilayered fibres from stretchable materials, and assumed that stretching the fibres would change the individual layers’ thicknesses, enabling them to tune the fibres’ colour. The results of these first efforts were published in Advanced Materials in 2013.

When Kolle joined the MIT faculty in the same year, he and his group, including Sandt, improved on the photonic fibre’s design and fabrication. In their current form, the fibres are made from layers of commonly used and widely available transparent rubbers, wrapped around highly stretchable fibre cores.

Sandt fabricated each layer using spin-coating, a technique in which a rubber, dissolved into solution, is poured onto a spinning wheel. Excess material is flung off the wheel, leaving a thin, uniform coating, the thickness of which can be determined by the wheel’s speed.

For fibre fabrication, Sandt formed these two layers on top of a water-soluble film on a silicon wafer. He then submerged the wafer, with all three layers, in water to dissolve the water-soluble layer, leaving the two rubbery layers floating on the water’s surface. Finally, he carefully rolled the two transparent layers around a black rubber fibre, to produce the final colourful photonic fibre.­­

Reflecting pressure


The team can tune the thickness of the fibres’ layers to produce any desired colour tuning, using standard optical modelling approaches customised for their fibre design.

“If you want a fibre to go from yellow to green, or blue, we can say, ‘This is how we have to lay out the fibre to give us this kind of [colour] trajectory,’” Kolle says. “This is powerful because you might want to have something that reflects red to show a dangerously high strain, or green for ‘okay.’ We have that capacity.”

The team fabricated colour-changing fibres with a tailored, strain-dependent colour variation using the theoretical model, and then stitched them along the length of a conventional compression bandage, which they previously characterised to determine the pressure that the bandage generates when it’s stretched by a certain amount.

The team used the relationship between bandage stretch and pressure, and the correlation between fibre colour and strain, to draw up a colour chart, matching a fibre’s colour (produced by a certain amount of stretching) to the pressure that is generated by the bandage.

To test the bandage’s effectiveness, Sandt and Moudio enlisted over a dozen student volunteers, who worked in pairs to apply three different compression bandages to each other’s legs: a plain bandage, a bandage threaded with photonic fibres, and a commercially available bandage printed with rectangular patterns. This bandage is designed so that when it is applying an optimal pressure, users should see that the rectangles become squares.

Bandage woven with photonic fibres gave clearest pressure feedback


Overall, the bandage woven with photonic fibres gave the clearest pressure feedback. Students were able to interpret the colour of the fibres, and based on the colour chart, apply a corresponding optimal pressure more accurately than either of the other bandages.

The researchers are now looking for ways to scale up the fibre fabrication process. Currently, they are able to make fibres that are several inches long. Ideally, they would like to produce meters or even kilometres of such fibres at a time.

“Currently, the fibres are costly, mostly because of the labour that goes into making them,” Kolle says. “The materials themselves are not worth much. If we could reel out kilometres of these fibres with relatively little work, then they would be dirt cheap.”

Then, such fibres could be threaded into bandages, along with textiles such as athletic apparel and shoes as colour indicators for, say, muscle strain during workouts. Kolle envisions that they may also be used as remotely readable strain gauges for infrastructure and machinery.

“Of course, they could also be a scientific tool that could be used in a broader context, which we want to explore,” Kolle says.

http://www.engineersjournal.ie/wp-content/uploads/2018/06/a-bandage1.jpghttp://www.engineersjournal.ie/wp-content/uploads/2018/06/a-bandage1-300x300.jpgDavid O'RiordanBiobiomedical,MIT,United States
Compression therapy is a standard form of treatment for patients who suffer from venous ulcers and other conditions in which veins struggle to return blood from the lower extremities. Compression stockings and bandages, wrapped tightly around the affected limb, can help to stimulate blood flow. But there is currently...